Carney All Seasons Blog: Archive for January, 2012

Heating Installation Guide: System Ventilation 101

Monday, January 30th, 2012

Maintaining Proper Ventilation for Combustion Systems

Anytime you maintain, retrofit, or replace a gas heating system in your Buckingham home you also need to be concerned with air quality. Combustion air is needed by all oil and gas heating systems to support the combustion process. This air is provided in some homes by unintentional air leaks, or by air ducts that connect to the outdoors. The combustion process creates several byproducts that are potentially hazardous to human health and can cause deterioration in your home. You can protect yourself from these hazards, as well as maintain energy efficiency, by ensuring that your chimney system functions properly and that your gas heating system is properly ventilated. In some cases, installing a sealed-combustion furnace can also help.

Chimneys

Properly functioning chimney systems will carry combustion byproducts out of the home. Therefore, chimney problems put you at risk of having these byproducts, such as carbon monoxide, spill into your home.

Most older gas furnaces have naturally drafting chimneys. The combustion gases exit the home through the chimney using only their buoyancy combined with the chimney’s height. Naturally drafting chimneys often have problems exhausting the combustion gases because of chimney blockage, wind or pressures inside the home that overcome the buoyancy of the gases.

Atmospheric, open-combustion furnaces, as well as fan-assisted furnaces, should be vented into masonry chimneys, metal double-wall chimneys, or another type of manufactured chimney. Masonry chimneys should have a fireclay, masonry liner or a retrofitted metal flue liner.

Many older chimneys have deteriorated liners or no liners at all and must be relined during furnace replacement. A chimney should be relined when any of the following changes are made to the combustion heating system:

When you replace an older furnace with a newer one that has an AFUE of 80% or more. These mid-efficiency appliances have a greater risk of depositing acidic condensation droplets in chimneys, and the chimneys must be prepared to handle this corrosive threat. The new chimney liner should be sized to accommodate both the new heating appliance and the combustion water heater by the installer.

When you replace an older furnace with a new 90+ AFUE appliance or a heat pump. In this case, the heating appliance will no longer vent into the old chimney, and the combustion water heater will now vent through an oversized chimney. This oversized chimney can lead to condensation and inadequate draft. The new chimney liner should be sized for the water heater alone, or the water heater in some cases can be vented directly through the wall.

Other Ventilation Concerns

Some fan-assisted, non-condensing furnaces, installed between 1987 and 1993, may be vented horizontally through high-temperature plastic vent pipe (not PVC pipe, which is safely used in condensing furnaces). This type of venting has been recalled and should be replaced by stainless steel vent pipe. If horizontal venting was used, an additional draft-inducing fan may be needed near the vent outlet to create adequate draft. Floor furnaces may have special venting problems because their vent connector exits the furnace close to the floor and may travel 10 to 30 feet before reaching a chimney. Check to see if this type of venting or the floor furnace itself needs replacement. If you smell gases, you have a venting problem that could affect your health. Contact your local utility or Buckingham heating contractor to have this venting problem repaired immediately.

Chimneys can be expensive to repair, and may help justify installing new heating equipment that won’t use the existing chimney.

Continue Reading

Tags: , , , , , ,
Posted in Heating | Comments Off on Heating Installation Guide: System Ventilation 101

How Tightly Should You Seal Your Home?

Friday, January 27th, 2012

More and more products and solutions are available to us these days to help seal our Warrington homes off from the outside world. The idea is that by keeping outside air out, our homes are more energy efficient and healthier, because all pollutants and pathogens are barred from entry.

This is a good idea in theory, but it can have its drawbacks. Most notably, sealing your home up too much can be bad for your family’s health. If your home is sealed too tightly such that there is not enough air flow from within the home to the outside and vice versa, then the indoor air just…stays indoors.

That means that all the sneezes, coughs, dust, dander, smoke and carbon dioxide stay inside with it. All that stuff can make you sick, completely flying in the face of your efforts to stay healthy by sealing your home.

Now, that’s not to say that sealing your home is a bad thing. Using LEED glass in your windows does keep heat in and increase heating efficiency. Air filters do help eliminate pollutants and pathogens from the outside than can make you sick. Good insulation and intact ductwork do help keep your home comfortable and efficient in both the cold and hot months.

So, sealing your home is not a bad idea. The trick is to not go overboard and seal it up so tightly that you are crossing the threshold from having a healthy home to having a giant Petri dish. You want to have a home that is insulated, but not vacuum sealed. You want a home with filtered air, but still plenty of air exchange with the outside world.Thankfully, mechanical ventilation is a way to both keep your home energy efficient and keep your indoor air from getting stale.

To help you with this endeavor, there are guides available online, such as at the ENERGY STAR website. In addition, it is a good idea to consult with a professional and ask plenty of questions when building a new home or making improvements to your current one. A qualified technician will know how to insulate and ventilate your home properly to protect your family’s health.

Continue Reading

Tags: , , ,
Posted in Indoor Air Quality | Comments Off on How Tightly Should You Seal Your Home?

Energy Efficiency Tips Everyone Should Know

Wednesday, January 25th, 2012

Before you decide which upgrades will make your Willow Grove home more efficient, it would be best to get a home energy audit. You can do this yourself with a few simple tests, or you can hire a professional auditor. The auditor will use advanced equipment and techniques, such as blower doors and infrared cameras, to detect air leaks and places that need more insulation.

When your home is properly insulated and sealed, here are some upgrades you’ll want to think about to make your home more efficient.

High-Efficiency Furnaces & Heat Pumps

If you have an old single-stage furnace, it is time to upgrade. These furnaces were designed to run on two settings—either off or on, and when they are on, they run at full speed. Not only do they lose heat this way, but they also take longer to warm up your home. The new two-speed and multispeed models run at lower speeds to maintain a constant temperature. You can also buy ones with variable-speed blowers that operate on various speeds, which are the most efficient. Heat pumps are a good option if you need both heat and A/C in your home. While most heat pumps are manufactured to be efficient by design, the newer models are the most efficient way to heat and cool your home. If you have a heat pump older than 15 years, talk to an HVAC technician about a heat pump replacement.

Solar & Tankless Water Heaters

When you’ve upgraded your heating system, it may be time to install a more efficient water heater. Solar water heaters are gaining popularity, and they are the most efficient way to save hot water if certain factors are in place, such as sunlight exposure and high fuel costs. Tankless water heaters heat your water with individual units located near hot water applications. You also have the option of installing a single, whole-home tankless water heater, or for appliances that use more hot water, such as dishwashers and washing machines, you can install tankless models just for their use.

Water-Saving Toilets & Low-flow Plumbing Fixtures

Duel flush, or water-saving toilets are an excellent choice for an upgrade if you want to save water. These toilets use less water overall, and you have the option of using more or less water each time you flush. Installing low flow faucets and fixtures can also provide up to 60% in utility savings. Low flow plumbing fixtures reduce the flow rate for each fixture or application, which reduces the overall amount water used in the home. These are a good option if you’ve installed a tankless water heating system. Your tankless water heaters will be more efficient if the sum of the flow rate total for every fixture in the home is lower.

Don’t hesitate to call Carney Plumbing, Heating & Cooling if you have any questions about upgrading your Willow Grove home.

Continue Reading

Tags: , , , , , ,
Posted in Energy Savings | Comments Off on Energy Efficiency Tips Everyone Should Know

HVAC Installation Guide: Where to Place a Thermostat for Accurate Heating

Monday, January 23rd, 2012

It’s easy to forget that with your furnace in the basement churning away all day to keep your Lansdale home warm, but your thermostat is the single most important device in ensuring your home is heated to the temperature you want. If it stops working or it misreads the temperature inside your home, your furnace won’t know what temperature it actually is and will turn on and off at the wrong time.

Where Not to Place Your Thermostat

To avoid inaccurate readings, avoid placing your thermostat in the following locations:

  • Direct Sunlight – Direct sunlight will almost always increase the perceived temperature of the thermostat. Unless you live in a greenhouse, this will be very uncomfortable for everyone in your home.
  • Windows – Windows can result in direct sunlight and breezes. If the windows are not properly sealed, cold air can blow in and make it seem cooler in your home than it really is. In any of these cases, your thermostat will misread the indoor temperature.
  • Drafts – Drafts from improperly sealed doors, windows, or anything else in your home can negatively impact the thermostat.
  • Heat Vents – Don’t place your thermostat near a radiator or heat vent where it is likely to be warmer than anywhere else in the house.
  • Kitchens – Kitchens tend to be warmer than other rooms in the house, especially when in use. Avoid placing a thermostat here unless you have a zone control system and your kitchen is separate from other rooms.

A properly placed thermostat will ensure your home is heated or cooled to the temperature you desire regardless of outdoor conditions. If you’re unsure whether your thermostat is calibrated properly, check the temperature with a separate thermometer in a different location in the same room. If it is significantly warmer or cooler in one place than another, try to determine which is more indicative of the actual comfort level in your Lansdale home. When properly located, your thermostat should never be an issue again.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on HVAC Installation Guide: Where to Place a Thermostat for Accurate Heating

What Is the Best Temperature to Heat My Home?

Friday, January 20th, 2012

Saving on energy costs is important for every Gwynedd Valley homeowner, but it’s not always clear what the average temperature would need to be in order to lower your heating bills. Generally, it’s best not to turn your thermostat above 68°F when you are at home, and to turn it down ten to fifteen degrees when you leave the house or while you’re sleeping. This can save up to 15% on your heating bills, but keep in mind that this percentage is greater in milder climates than colder climates.

Remembering to turn down the heat when you don’t need it is the biggest challenge when trying to save heat. One of the easiest ways to do this is to install a programmable thermostat that allows you to set the times you want the heat turned up or down. This will ensure that you are consistent with turning your heat down, and you can set it to turn on before you get up in the morning so that the house is already warm when you get out of bed. Depending on the brand and setting options, programmable thermostats are relatively inexpensive and easy to install.

One common misunderstanding about thermostats is that it takes more energy for the heating system to warm up the house after the thermostat has been turned down for an extended period of time. The belief is that the energy saved by not producing heat is cancelled out by the work it takes to heat up the home again.  This is not the case, however, since the lower the temperature is inside your home, the longer it takes to lose heat. You will actually save more energy the longer the thermostat is set at a lower temperature. Conversely, the same theory applies to the cost of cooling your home in the summer, since higher interior temperatures slow down the flow of heat into the home.

Overall, if you want to save on heating costs, you should keep your home below 70°F as much as possible, and turn down the thermostat about fifteen degrees when you don’t need the heat. Closing off the doors and vents to unused rooms will also save energy, and you can put on extra clothing to help remind you to turn down the heat a few degrees while you are home. You don’t have to spend a fortune to heat your Gwynedd Valley home if you are consistent with your thermostat settings.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on What Is the Best Temperature to Heat My Home?

Comparing High-Efficiency and Mid-Efficiency Furnaces

Wednesday, January 18th, 2012

Whenever you are in the market for a new furnace for your Perkasie home, there are many models to choose from.  Many of the furnaces manufactured within the last few years are high-efficiency furnaces with a high AFUE rating (AFUE measures the amount of fuel the furnace converts into heat). When people refer to a mid-efficiency furnace, they are usually talking about older furnaces.

Single-stage furnaces were considered to be an efficient heating system when they were manufactured, but compared to newer furnaces, they use up a lot more energy than they need to. Single-speed furnaces are designed to run at full capacity until the temperature inside the home reaches the thermostat setting. After they shut off, the home not only loses heat, but the furnace will also take longer and burn more fuel when it cycles on again.

Newer, two-speed and multispeed models run consistently at lower speeds, and the ones with variable-speed blowers are even more efficient because they can operate at various levels. These models will also automatically adjust to the thermostat to maintain a constant temperature, which saves energy by keeping the home at a consistent temperature so that there’s little heat loss.

When shopping for a new furnace, keep in mind that the AFUE ratings for multispeed and variable-speed furnaces only determine the efficiency of the actual furnace. If you are upgrading your old, mid-efficiency furnace to a high-efficiency furnace, you should make sure that your Perkasie home is properly insulated and sealed.  You could also consider upgrading any older doors and windows to more efficient double-paned ones, or you can also install storm doors and windows.

Continue Reading

Tags: , , , , ,
Posted in Heating | Comments Off on Comparing High-Efficiency and Mid-Efficiency Furnaces

Happy Martin Luther King Day from Your Bucks and Montgomery County Plumbing and HVAC Contractor!

Monday, January 16th, 2012

Happy Martin Luther King Day! Many people consider this day a call to service, and there are so different many ways you can help your community, from lending a hand to a neighbor to donating food. Take a moment to think about how you make a difference in someone’s life today; even a small act of kindness can have a big effect. Help us make our community a better place!

Continue Reading

Tags:
Posted in Holiday | Comments Off on Happy Martin Luther King Day from Your Bucks and Montgomery County Plumbing and HVAC Contractor!

What to Check If Your Furnace Isn’t Lighting

Friday, January 13th, 2012

If your furnace isn’t lighting properly and your family is starting to suffer because of it, there are a number of possible problems you should check for before calling a Harleysville professional. Some of these issues can be fixed quickly by you while others may be signs of a serious problem that needs professional attention right away.

Checking the Pilot Light

If you have a gas furnace, the first step is to check the pilot light and ensure it is still working properly. If the pilot light is still on but goes out when you try to light the furnace or simply won’t stay on when you relight it, you may need to have the gas valve replaced. In some cases, it is as simple as the pilot light not being large enough and the gas blowing out the light.

This happens when gas enters the chamber and doesn’t ignite right away. When it does ignite, which happens after more gas enters the chamber, the extra force of the ignition will blow out the light. This is still a problem and should be inspected to ensure you don’t have any potential gas related issues.

Still Not Lighting

If you don’t have a pilot light or the unit still isn’t lighting, it may be an electrical issue. Electrical ignitions for gas furnaces should spark when the thermostat is turned on, so if it doesn’t you know that the switch or relay are bad.

If you smell gas or anything similar in the room where the furnace is located, you should immediately turn off the unit and call your gas company, followed by a technician. There could be a leak causing low pressure that results in your pilot light going out. Whatever the case, you need someone to look at it immediately.

Your furnace should always turn on when you flip the switch and if it does not, assume there is a problem. If you cannot find the problem yourself and easily fix it, you should call a Harleysville professional. The risk inherent in an improperly working furnace (especially gas or oil) is too high to ignore.

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on What to Check If Your Furnace Isn’t Lighting

Causes of Delayed Furnace Ignition

Wednesday, January 11th, 2012

Delayed ignition is usually accompanied by a loud banging or booming sound that resembles a small explosion in your gas appliance. In your New Britain home’s furnace, this can be terrifying and should never be ignored.

What Causes Delayed Ignition

Delayed ignition usually happens when you first turn on your furnace, often after a long delay between use, so usually early in the fall or late in the spring when you don’t necessarily have it on every day of the week.

What happens is moisture builds up over the course of a period of inactivity and begins to corrode the firebox in your furnace. That corrosion builds up to the point that it starts to block the ports that feed gas into the burners. When these ports get blocked, the burners down the line cannot light and when you flip the switch, they won’t light immediately.

Of course, while rust and corrosion are a risk, lint and dust can be equally problematic (and are more common if you don’t have your furnace cleaned properly each fall). Sulfur build up is also a possibility, as it is left behind by burning natural gas. It will appear as a layer of white on the surface of the burners or the pilot light.

When all of this happens and the ports are not cleaned properly, gas will build up in the chamber after it is turned on and, when it finally ignites, create the small boom sound. It doesn’t just sound like an explosion – it is one – and if ignored, it can become incredibly dangerous.

Solving the Problem

Delayed furnace ignition is an easy problem to avoid. All you need to do is have your furnace cleaned properly before turning it on each fall. A New Britain heating technician will clean the burners and ports and remove any dust, lint, rust or sulfur buildup that might block ignition and cause a delay.

When replacing your furnace, look for a device with corrosion resistant materials. You can learn more about these when it comes time to replace your furnace from a technician. Most importantly, be careful. It may be a small problem now, but if left to build up over time, that small boom can become a much larger one.

Continue Reading

Tags: , , ,
Posted in Heating | Comments Off on Causes of Delayed Furnace Ignition

What Is a Gravity Furnace?

Monday, January 9th, 2012

A long time ago, gravity furnaces were a very popular means of heating a home. Instead of pressurizing and blowing air through vents to each room of your Buckingham home, a gravity furnace used gravity to move warm air between rooms.

The operation of these furnaces is pretty simple. When turned on, the furnace, which is located in your basement, burns fuel like gas or oil and produces heat. That heat is vented through ductwork to the top level of your home using the natural properties of gravity (hot air rises). The hot air exits vents as it travels up in the home and releases heat into the room.

Why to Replace a Gravity Furnace

While gravity furnaces can work nearly forever and have very few mechanical problems, they are incredibly expensive to operate and take up a lot of space. Due to the sheer volume of ducts needed to distribute air throughout your home and the cost of heating enough air to ensure it rises properly, you’re dealing with a heating efficiency of 50% or lower.

In fact, about half the energy you consume to heat air in a gravity furnace gets pumped straight out through the chimney. It’s a complete waste of money and a replacement will start saving you money almost immediately.

Newer furnaces have efficiency ratings of up to 95% which makes them nearly twice as efficient as gravity furnaces. Additionally, they take up less space and with modern components, you can install newer devices like zone controls, electronic readout and display and more. It’s a fantastic way to enjoy steady, reliable heat in your home without having to invest a fortune in the fuel needed to operate it.

Comfort Matters

Another thing to consider is the comfort level of your home. Because gravity furnaces release warm air through the middle of the house and cold air comes back down along the walls, homes that have them are rarely comfortable except in the middle of the house. Forced air furnaces with blower fans are much more efficient at distributing heated air and matching the thermostat settings you select.

Continue Reading

Tags: , , , ,
Posted in Heating | Comments Off on What Is a Gravity Furnace?