Posts Tagged ‘Montgomery County’

« Older Entries
Newer Entries »

Unclogging a Floor Drain: A Tip From Buckingham

Wednesday, September 28th, 2011

215.346.7160

It is never fun to wander down into the basement of your Buckingham home only to find that your floor drain has backed up. This is not a situation that will take care of itself and you want to get it under control as quickly as possible. While there are certainly plenty of things you can do to try and unclog a floor drain on your own, there are quite a few potentially complicating factors to consider as well.

First of all, you should make sure that no one in the house turns on any running water for anything until the drain has been unclogged. The floor drain in your basement is usually the last stop on the line for all of the water used in your house, and so any running water anywhere above will only cause more water to back up in the basement. Of course, if you cannot use any running water anywhere else in your house, it is even more imperative that you are able to unclog the floor drain quickly.

If you happen to have a snake on hand, this may be the best option to try first. However, it can be a bit difficult to get the snake to make the sharp turn typical of these types of drains not long after the pipe descends below the floor. That is not to say that it cannot be done, but you should be aware that you need to make sure the snake turns the corner before it will be useful to you at all.

If you do not have a snake of your own, you may still be able to take care of the blockage without calling in a professional plumber. But first you have to find it. Depending on the layout of your drainage system, this may be easier said than done. You can also make a pretty big mess if you open up various sections of pipe looking for the blockage, so be aware and make sure you have something in place to catch the runoff and debris that may come out of the pipes when you open them.

You may also run into trouble if the blockage is actually outside of your house in the larger sewer line that runs to the street. Unclogging a drain with this type of problem is generally a job for a professional and there is very little you will be able to do on your own.

Tags: , , , ,
Posted in Plumbing | Comments Off

The Technology of Video Pipe Inspection: Some Pointers From Souderton

Monday, September 26th, 2011

215.346.7160

Let’s face it – technology is the answer for everything, from Souderton to Maple Glen. If it’s mechanical, it has been affected by technology. The world of plumbing is no exception. Technology now makes it possible for people to look inside the piping in their home – to get the “inside story” on why a pipe is blocked up or why water is flowing too slowly. A trained expert can use video pipe inspection technology to quickly diagnose a problem in order to find a solution.

So what types of technology are available today? Before we get to that, remember that technology is fluent. By the time you read this blog there may be something new to make this material outdated. The best way to keep up with the latest technology of video pipe inspection is to talk to your local plumbing professionals and check out updates on the Web.

The technology you will see in your home can be viewed live or via digital recording. The camera and its scope can grab a birds-eye view of the pipe without the need to unscrew fittings and elbows and without having to make a mess of things.

Plumbers making a service call who use video inspection will usually show homeowners some live pictures from inside their pipes or use a digital reproduction in their sales presentation. In either case, the camera doesn’t lie and repairs are quickly supported by video evidence.

Here are some of the components involved in the technology of video pipe inspection. First and foremost is the camera itself, which usually will have high definition image display, recording, and playback capabilities. Images can be stored on flash cards for downloading onto other computers or to the Web. The lens of the camera is mounted into the head of the scope, which could be made of fiber optic or fiberglass material. The scope or “snake” comes in a variety of lengths. Images from the camera can viewed on monitors of various sizes in color or black-and-white.

Other options may include audio capabilities for a plumbing professional to record what the camera sees and explain the problems and solutions to homeowners via voiceover technology.

According to one plumber who utilizes this type of technology, video pipe inspection provides “an assessment of pipe’s structural integrity, detection of blockages, breaks or defects, still image/video footage for client use, and first-time mapping or updates.”

If you want to utilize the latest technology to diagnose pluming problems in your home, call your local plumbing professional and ask for a video pipe inspection.

Tags: , , , , ,
Posted in Plumbing | Comments Off

Top 4 Upgrades For Your HVAC System: A Guide From Ambler

Wednesday, September 7th, 2011

215.346.7160

Your HVAC system is a trusted part of your Ambler home’s comfort system. Without it you would be cold in the winter, hot in the summer, and breathing in contaminant laden air year round. So, it’s important that you install the best systems and subsystems available for your HVAC system. Here are some options to keep in mind when looking for ways to get the most from your heating and cooling.

  • Humidity Control – Don’t rely on your air conditioner to remove humidity in the summer. A dehumidifier is more energy efficient and reduces stress on your air conditioning system when the humidity gets high. In the winter, humidification allows your home to hold more heat, effectively increasing the efficiency of your heating system.
  • Air Filtration – Every air conditioning system and furnace comes with some form of air filtration, but is it enough? Standard filters are effective, but they are not always comprehensive. A good HEPA quality filter for your air handler and duct system will severely reduce the number of contaminants in your air supply and ensure that you and your family feel much better year round.
  • Ductwork Upgrades – If your ductwork is old, battered or starting to show its years, an upgrade may be in order. If nothing else, having your ductwork cleaned on a regular basis removes excess mold, dusty, pollen, debris and other pollutants that can affect your health and the quality of the air you breathe. Schedule annual cleanings of your ductwork and a biannual inspection to check for cracks and leaks.
  • Air Quality Controls – Beyond air filtration, you can upgrade your air handler’s ability to remove pollutants with a dedicated air cleaner and UV lights. These systems are installed in your air handler and/or ductwork to remove advanced pollutants like bacteria and mold and remove smaller particles including smoke, gas, and exhaust. Which system you need will depend on the level of contaminants in your home, so make sure you check with a contractor before choosing anything.

These upgrades are a great way to get more out of your HVAC system – in terms of both comfort and safety. Discuss your options with a contractor today to learn more.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

What Does the EPA Do for Indoor Air Quality: A Question From Gwynedd

Wednesday, August 24th, 2011

215.346.7160

There are a number of agencies in the United States dedicated to protecting the health and wellbeing of citizens. What does that mean for you in Gwynedd? It means many of the rules and regulations related to indoor air quality are directly overseen by the EPA and the US government. For a better idea of how this impacts your currently lifestyle, here’s a quick look at what the EPA does.

Formation

The Environmental Protection Agency was formed in 1970 by Richard Nixon and the US Congress to oversee the regulation and oversight of air, water, land and hazardous waste. In short, the EPA works to keep our environment clean and safe.

The EPA and Homeowners

While much of what the EPA does relates to corporate pollution, regulations for manufacturing and consumer products, and development of safe methods of production for things like oil, food and water, the EPA has a big hand in ensuring your home stays safe.

Specifically, the EPA started and oversees the Energy Star program to help consumers purchase appliances and HVAC systems that use the least possible energy. Additionally, the EPA oversees the measurements and minimum requirements for home insulation and ventilation. This has as direct impact on indoor air quality.

Current EPA regulations are based on the ASHRAE Standards for low rise buildings and has been revised in the last two decades to ensure proper ventilation and insulation to reduce energy waste and maintain clean, fresh air.

The clean air act has a big impact on how homes are ventilated and maintained and the EPA does a lot of public service work to educate the public on ways to stay safe, including a recent campaign to get your home tested for radon – a potentially life threatening gas that can exist in any home, regardless of age.

Getting to Know the EPA

If you have an indoor air quality or suspect there may be issues in your home, one of the best resources on the Internet is the EPA’s indoor air quality website. It contains laws and regulations that impact your home (if you plan on remodeling or adding on to your home) and dozens of resources for testing and understanding the levels of pollutants in your home.

Tags: , , , , ,
Posted in Indoor Air Quality | Comments Off

Is Geothermal for Me? A Question From Lansdale

Friday, August 12th, 2011

215.346.7160

Geothermal heating is a great alternative to other types of home heating systems in Lansdale. It is safe and efficient, costs very little to operate and makes use of a great renewable resource right below our feet. But is it right for you? Well, geothermal heating may be the right choice for many people, but there are many things to take into account before you can determine whether or not it is the best choice for your home.

The first important thing to understand when you are trying to decide whether or not to go with geothermal heating is how one of these systems actually works. A geothermal system heats your home by extracting heat from the ground and then transferring that heat into your indoor air. This happens when liquid, usually water or antifreeze, passes through a loop of pipes installed several feet below the ground.

The liquid absorbs heat from the ground, which in the winter is always warmer than the air, and carries is back up to an air handler inside your home where that heat is allowed to disperse into the air. Once the air is heated, the air handler blows the air through a system of ducts throughout your house, providing a constant stream of heated air to all areas of your home. The liquid, on the other hand, simply cycles back through the ground loop to pick up more heat and repeat the same cycle over again.

Because a geothermal heating system does not actually generate heat, it requires very little energy to operate. This means that it is both very cheap for you to run and environmentally friendly. But since installing a geothermal heating system involves putting pipes in underground, it can be pretty expensive initially. However, as long as the amount you save every month on your heating costs is enough to offset the high initial price of installation, it is worth it to put down the money up front.

Another alternative, of course, is a more traditional air source heat pump. These are much cheaper to install and nearly as cheap to run. However, air source heat pumps are not as efficient when the air temperature gets below freezing as a geothermal system can be. If you live in an area with harsh winters, the geothermal heat pump is a better option than an air source unit.

Tags: , , , , , ,
Posted in Geothermal | Comments Off

Scald Free Showers and Bathtubs: Scald Prevention Methods

Friday, July 22nd, 2011

215.346.7160

One of the worst things that can happen to you in a shower is when a sudden blast of scalding hot water strikes you unexpectedly. This is a problem for many people and usually happens when someone turns on the cold water at another tap in the house. When that occurs, the cold water that you were using to regulate the temperature in your shower becomes temporarily unavailable and the hot water takes over.

This usually does not last long, and even if it does, you will likely jump out of the way quickly. But for the moment you are underneath that scalding hot water, some serious damage can be done, particularly to older people or young children whose skin is not as thick as that of an average adult. Also, in trying to get out of the way of the hot water in a slippery bathtub, many people have accidentally fallen and injured themselves more seriously.

So what can be done about these sudden and unexpected blasts of hot water? Well, recent developments in shower and bathtub technology have made it possible for scald free shower and bathtub fixtures to reach the market. These products are designed to maintain a consistent temperature in your shower no matter what type of water or how much is being used elsewhere in the house.

These scald free showers can compensate for the dip in cold water pressure that occurs when someone flushes a toilet in another bathroom or turns on the water in the kitchen. This is accomplished by the addition of a diaphragm that can immediately adjust to any variations in either hot or cold water pressure. With this technology in place, you will never need to worry about being scalded in the shower again.

Of course, these scald free shower heads and bathtub fixtures can cost a bit more than their conventional counterparts. But they are well worth it, especially if scalding water is a problem in your shower on a regular basis. You need to be able to keep yourself and your family safe in the shower and scald free showers are the best way to do that.

Tags: , ,
Posted in Plumbing | Comments Off

How a Water Softener Works

Monday, July 18th, 2011

215.346.7160

You use water for many things. It is necessary for bathing, cooking, washing clothes and for drinking. But the water we use in our homes is not pure. It has plenty of other minerals and additives suspended inside. While some of these, like fluoride, are intentionally added to the water supplies in certain areas, some others get in by chance.

Aside from actual pollutants, the additives you may be the most concerned about finding in your water are calcium and magnesium. These minerals are picked up by water as it moves through the ground, and the more of them that get into your home water supply, the harder that water will be.

The term hard water is used to describe water with high levels of calcium and magnesium present. These minerals are not actually dangerous to us, but they can cause all sorts of problems for your indoor plumbing and other household systems. For instance, hard water will leave deposits of these minerals on the insides of pipes and on sinks, faucets and bathtubs.

Residue will also build up in appliances like coffee makers, dish washers and washing machines. Over time these buildups can become a real problem and you may have to pay for costly repairs or need to replace large appliances.

In order to avoid these types of complications, your best bet is to have a water softener installed. These systems can be connected directly to your home water source and they are able to remove excess calcium and magnesium from the water before it ever reaches any of your indoor plumbing or appliances.

Water softeners generally remove these minerals by attracting the positively charged calcium and magnesium particles with a tank full of negatively charged polystyrene particles. In this system, the calcium and magnesium are replaced by sodium ions as they move through the water softener, thereby maintaining the overall balanced composition of the water. Once the water has passed through and the calcium and magnesium have been left behind, the water softener will flush them out and prepare to absorb another wave of hard water minerals.

Tags: , , , ,
Posted in Plumbing | Comments Off

Quick Tips on Toilets

Monday, July 11th, 2011

215.346.7160

Quite simply, everyone needs to have a working toilet in their home. Of course, when we do, we tend to take it for granted. Most people really do not know much about how their toilets work and how much water they use, and acquiring that information can be beneficial to you for several reasons. Toilet tips can help you save money, catch problems early and generally get the most out of your toilet.

Water-saving devices are always useful on toilets. Even if you did not buy a water-saver toilet to begin with, you can convert your regular toilet into one by installing a toilet cycle diverter. These great gadgets actually direct some of the water from each flush back into the tank rather than allowing it to run into the toilet bowl itself.

What this does is allow the tank to fill up faster. Less water goes down with each flush and less water is needed to fill up the tank. These devices are relatively easy to install yourself and they can save you a ton in the long run. In fact, the average toilet cycle diverter can conserve up to a gallon of water per flush.

You will also benefit from learning about how your toilet works because it can enable you to catch problems early when they are easy to correct. You may or may not be able to do the corrective work yourself, but at least you can call out a plumber earlier rather than later.

Fixing toilet problems early hopefully means that you will not have to go without a toilet for very long, if at all. And the repairs that you need should be relatively minor and inexpensive. When toilet issues are allowed to persist, they can turn into a much bigger plumbing problem and cause a great deal of inconvenience to you and your family.

One of the most common toilet problems is leaks. A leaky toilet can have all kinds of symptoms, but the bottom line is that it is probably costing you money on your water bill each month. Also, leaks will only get bigger as time goes on, so you will be much better off if you fix them early. Phantom flushing and continuous running are both signs that your toilet is leaking, and the earlier you do something about it, the better off you will be.

Tags: , , , ,
Posted in Plumbing | Comments Off

How Much Water Does a Leaky Faucet Waste?

Monday, July 4th, 2011

215.346.7160

A leaky faucet is obnoxious for more than one reason. It is incessant, it represents a problem that will probably only grow worse, and it can cost you money on your water bill. Beyond all of that, it wastes a lot of water, putting undue stress on the environment. But, how much water does a leaky faucet actually waste? It may not seem like much, but when added up over a period of time, that leaky faucet’s impact can be fairly substantial.

Okay, so a single drip every couple seconds may not seem like a lot of water. But, think about it this way. If you let your faucet drip every day, twenty four hours a day, it is definitely going to add up. Imagine what would happen if every faucet in your home was dripping or every faucet in your neighbourhood. It would not seem like such a small amount of water anymore.

In terms of how much water is actually wasted, it is impossible to tell for certain. After all, every drop of water from a faucet is a different size and falls at a different rate. But, for the most part the water coming from a faucet (according to the US Geological Survey) is between 1/5 and 1/3 of one milliliter. Using those calculations and 1/4 of a milliliter as an average, the USGS estimates that roughly 15,140 drips from a faucet equals one gallon of water.

It may not seem like much. After all, fifteen thousand drops is a LOT of drops. But, if your faucet dripped once every second every day, all day, it would only take four and a half hours to reach one gallon. Every day you would waste 5 gallons of water or 2,082 gallons per year. That is 10% of the average water used by a standard 3.5 gpf toilet on a daily basis. Now, imagine what happens if you have more than one drippy faucet, or if your bathtub leaks which will drip more water at a time or if the leak is larger than the average size.

In short, the cost of a leaky faucet may not seem like much, but as time passes, it can really add up and if it is not taken care of, the cost will only grow as the leak gets bigger and potentially new leaks start in other faucets of your home. Do not let it drip forever – take action now and cut down on the environmental impact you have, as well as your bill.

Tags: , , , ,
Posted in Plumbing | Comments Off

Whole House Fans vs. Attic Fans

Friday, July 1st, 2011

215.346.7160

Air temperature in your home is a big issue in the summer. The cost of maintaining your air conditioner as it runs nonstop for hours at a time can be very high – as much as $4,000 for a single year of cooling. That’s why a lot of families turn to fan solutions to reduce how much they spend on their AC units each year.

How Fans Work

A fan draws in outdoor air to your home. That outdoor air will cool your home when the outside temperature is cooler than the indoor temperature. If the weather outside gets much warmer than 80°F, you will probably still need to use your air conditioner at least a little, but if it’s in the 70°F-80°F range, the temperature inside can be maintained simply by blowing cooler outdoor air into your home.

A whole house fan solves this problem by pumping fresh air into your home through the ductwork you already have in place. When the temperature outside is low enough, you’ll enjoy a much steadier, more comfortable level of cooling and save a lot of money.

However, for those that don’t want to install a completely new system for their entire house, attic fans offer a good chunk of savings as well.

Why Attic Fans Work

The idea behind an attic fan is simple. During the summer, all the heat in your home rises. Even with your air conditioning working at full capacity, heat will build up in the attic, especially if you don’t use that space and therefore don’t have any cooling ducts up there.

In some cases, attic temperatures can rise to 140°F or higher, which then raises the temperature of the rest of your home and forces your AC unit to work that much harder.

An attic fan is good because it takes the air from outside, almost assuredly cooler than 120°F and cycles it into your attic to keep the temperature lower. That simple fan can reduce indoor air temperature by as much as 40°F or 50°F and significantly reduce your air conditioner’s work load.

Which is Better?

Neither of these is better than the other. If you have low cooling costs and want to keep your attic from adding to them, an attic fan is perfect. However, if you want to cut into your cooling costs for all but the warmest months of the summer, a whole house fan may be the right option.

Tags: , , , ,
Posted in Indoor Air Quality | Comments Off

« Older Entries
Newer Entries »