Archive for the ‘Energy Savings’ Category

« Older Entries

New Britain Heating Tips: Five Ways to Save Heat That You Might Not Have Considered

Friday, February 3rd, 2012

215.346.7160

Finding new ways to lower the heating bills for your New Britain home is always a challenge. Maybe you’ve already insulated and sealed every crawlspace and crack, or you might have recently upgraded that old furnace, but there are always other ways to reduce heat loss in the winter.

Here are five ways to conserve heat that you might not have considered.

1. Insulate Recessed Light Fixtures

While recessed light fixtures save space and give you more control over lighting and design, such as task lighting in kitchens, they can be a hidden source of heat loss. Feel around your recessed lighting fixtures to see if there’s cool air or a draft. If you do, they could need more insulation. However, you have to be extremely cautious about what type of insulation you use around electrical wiring and fixtures. Check with the manufacturer, or call an electrician if you aren’t sure what  type of insulation to use.

2. Insulate Water Heater Tanks

Part of your heating bill each month goes to heating the water in your home. Whether you have a gas, electric, solar, or hybrid hot water heater, every water heater tank has an R-value that determines how much heat it loses. If you have a low R-value, your tank may need more insulation. Call a professional plumber or check your owner’s manual for the R-value of the model you own, but the general rule is that if the tank is warm when you touch it, you may need to buy a “jacket” for your water heater. These are fairly inexpensive, easy to install, and can be found relatively anywhere you buy insulation.

3. Open Curtains on South End

The southern end of your home will get the most sunlight in the winter. If you have curtains or blinds on your windows or doors, leave them open during the day, and make sure you close them at night. Opening them will help warm up the home naturally during the day, and closing them will help keep the cold air out and warm air in at night.

4. Storm Windows and Doors

Many homeowners know they have the option of upgrading old doors and windows that leak air, but not everyone can afford to upgrade all the doors and windows at once. You can also install storm windows and doors to help reserve heat. Before you start comparing prices, remember to measure, since measurements will affect the cost.

5. Close Fireplace Flue

Whenever your flue is open, you are losing large amounts of heat. Close the damper if the fireplace or chimney is not being used. You can also consider upgrading to a more air tight damper.

You can always call Carney Plumbing, Heating & Cooling whenever you have questions about lowering your heating costs for your New Britain home.

Tags: , , , , ,
Posted in Energy Savings, Heating | Comments Off

Willow Grove Energy Efficiency Tips

Wednesday, January 25th, 2012

215.346.7160

Before you decide which upgrades will make your Willow Grove home more efficient, it would be best to get a home energy audit. You can do this yourself with a few simple tests, or you can hire a professional auditor. The auditor will use advanced equipment and techniques, such as blower doors and infrared cameras, to detect air leaks and places that need more insulation.

When your home is properly insulated and sealed, here are some upgrades you’ll want to think about to make your home more efficient.

High-Efficiency Furnaces & Heat Pumps

If you have an old single-stage furnace, it is time to upgrade. These furnaces were designed to run on two settings—either off or on, and when they are on, they run at full speed. Not only do they lose heat this way, but they also take longer to warm up your home. The new two-speed and multispeed models run at lower speeds to maintain a constant temperature. You can also buy ones with variable-speed blowers that operate on various speeds, which are the most efficient. Heat pumps are a good option if you need both heat and A/C in your home. While most heat pumps are manufactured to be efficient by design, the newer models are the most efficient way to heat and cool your home. If you have a heat pump older than 15 years, talk to an HVAC technician about a heat pump replacement.

Solar & Tankless Water Heaters

When you’ve upgraded your heating system, it may be time to install a more efficient water heater. Solar water heaters are gaining popularity, and they are the most efficient way to save hot water if certain factors are in place, such as sunlight exposure and high fuel costs. Tankless water heaters heat your water with individual units located near hot water applications. You also have the option of installing a single, whole-home tankless water heater, or for appliances that use more hot water, such as dishwashers and washing machines, you can install tankless models just for their use.

Water-Saving Toilets & Low-flow Plumbing Fixtures

Duel flush, or water-saving toilets are an excellent choice for an upgrade if you want to save water. These toilets use less water overall, and you have the option of using more or less water each time you flush. Installing low flow faucets and fixtures can also provide up to 60% in utility savings. Low flow plumbing fixtures reduce the flow rate for each fixture or application, which reduces the overall amount water used in the home. These are a good option if you’ve installed a tankless water heating system. Your tankless water heaters will be more efficient if the sum of the flow rate total for every fixture in the home is lower.

Don’t hesitate to call Carney Plumbing, Heating & Cooling if you have any questions about upgrading your Willow Grove home.

Tags: , , , , , ,
Posted in Energy Savings | Comments Off

Water and Energy Saving Tips From Solebury

Friday, September 23rd, 2011

215.346.7160

The cost of the heat, air conditioning and water supply to your Solebury home continues to rise – it’s no wonder you want to cut your bills so much. But, how can you do that without cutting into the creature comforts and conveniences you’ve gotten used to over the course of the last few decades? Here are a few simple energy and water saving tips to make your life easier.

  • Patching Leaks – Two of the biggest wasters of water are dripping faucets and leaky pipes. The amount of water wasted by a single drip every second could provide for multiple baths per year – it adds up fast. Not only are leaky faucets and pipes easy to fix; they tend to develop into bigger problems as time passes.
  • Drains and Flushing – If you put a piece of toilet paper in the toilet used to clean an eye or wipe the counter, don’t flush. It’s a waste of water. If you notice some extra toothpaste in the sink, don’t rinse yet. You can always use the water from brushing your teeth or washing your face to clean it out. Multi-task and minimize how much water goes down the drain to save water.
  • Fully Loaded – A partially filled washing machine or dish washer is a huge waster of water. Fill it up and wait to run the device until it’s at the brim – the same amount of water is used no matter how much is in the device.
  • Compost vs. Disposal – A garbage disposal wastes a tremendous amount of water (if you want it to run properly). So, instead of churning the disposal up, create a compost pile and save a great deal of water/energy. If you have a septic tank, a garbage disposal is especially bad for your home as it can fill the tank up quickly with solids.
  • Lower Water Flow – Don’t crank your faucets up to the max just to get a glass of water or to check for hot water. It’s a waste of energy and it’s often unnecessary, especially when waiting for water to hit the right temperature.

If you’re interested in getting the most out of your home’s water supply, there are hundreds of little ways to save water that will add up over time. These are just some of the easiest ways to get started. If you need more tips, contact your plumber.

Tags: , , , ,
Posted in Energy Savings | Comments Off

What Is the Energy Star Label? A Question From Norristown

Friday, August 5th, 2011

215.346.7160

Any time you go out and buy any type of appliance in Norristown, you probably notice that some have a distinct mark that signifies them as Energy Star appliances. That sounds like a good thing, of course, but what does it actually mean? Should you always buy an Energy Star model over another type?

The Energy Star label was originally developed to help consumers more easily recognize appliances that are more energy efficient than the average. In order to obtain an Energy Star seal of approval, any device must meet very strict guidelines when it comes to energy efficiency.

What that translates into for you as a consumer is a lower monthly energy bill when you buy Energy Star appliances. Of course, once they have obtained an Energy Star labels, manufacturers can charge whatever they want for their product, and it is not unusual to pay more for a model that is certified an Energy Star.

However, as long as the potential savings over time that you will get by using the Energy Star model as opposed to one that is not as energy efficient outweigh the difference in initial purchase price, it is worth it to spend a bit more on the Energy Star model.

Keep in mind, though, that just because a produce meets the Energy Star guidelines for energy efficiency does not necessarily mean that it is a superior product in terms of quality or overall effectiveness. Plus, not all Energy Star appliances are created equal. You should still do your research and pick out the product that will both save you the most money and has the best chance of getting the job done right.

Another benefit to Energy Star products is that, because they use less energy when they run, they also have a smaller impact on the environment than a model that uses a greater amount of energy to perform the same tasks.

Overall, it is definitely worth taking a closer look at all of the Energy Star options out there when you are purchasing an air conditioning system or any other type of appliance. Using less energy is always a good thing both for your bank account and for the planet. But you also want to make sure you are actually getting the best product for your money. Ask your local professional about other energy saving options.

Tags: , , ,
Posted in Energy Savings | Comments Off

New Thermostats – Are they Worth the Investment?

Friday, February 4th, 2011

215.346.7160

When you are trying to save money around the house, a new thermostat is definitely worth looking into. Sure, your old thermostat works fine. But there are a lot of features available on newer models that can help you save money on your heating and cooling costs throughout the year.

And you do not need to wait until it is time to replace your home comfort system to upgrade your thermostat. Most thermostats can work with many different types of heating and cooling systems. So no matter what type of HVAC system you have or how old it is, you should be able to integrate some type of new thermostat into it.

But how can a new thermostat save you money? Well, they simply offer a lot of features that you can use to your advantage. For instance, even the most basic programmable thermostat can let you set different temperatures for different times of day. You can program the thermostat to turn the heat down during the day when no one is home and then you can have the heat switch back on just before you get home.

That way, you can come home to a nice, warm house without having to pay to heat it all day long when it is empty. Many newer thermostats also are more accurate and can provide more pinpoint control of your heating and cooling system. That means that you will not be wasting money because your heating system gets the actual temperature in your house up to 75°F when you only really need it to hit 72°F.

Newer thermostats help you to save money in a variety of ways, and that savings will more than pay for the cost of having a new thermostat installed. That is because thermostats are actually quite cheap and easy to install. A relatively basic programmable thermostat should not run you more than $100, and even if you opt for one of the more advanced systems out there, you will not pay more than a few hundred dollars.

That is a small price to pay considering the increased comfort possible with a state of the art thermostat and the potential for savings every month on your heating or cooling bills. Plus, you likely paid a considerable amount to have that state of the art HVAC system put in. It is worth paying just a bit more so that you can get the most possible out of it.

Tags: , , , , , ,
Posted in Energy Savings | Comments Off

How to Maximize Savings in Your Home

Wednesday, February 2nd, 2011

215.346.7160

When you are thinking about different ways you might be able to save money around the house, the tendency is to think big. Maybe you need to upgrade to a more energy efficient furnace, or it could be time to install a new central air conditioning system. Maybe it is even a good idea to switch to solar or geothermal power.

But before you do any of that, you may want to try some quick and easy ways to save money around the house with the equipment you already have. Here are 10 great ways to cut your power usage and keep those energy bills down without investing a lot in new equipment.

  1. Seal Up Your House – No matter how energy efficient the heating and cooling systems are in your house, you will be using more energy than necessary if your house is not tightly sealed. Make sure there are not cracks or places where drafts can get in and you will start saving money right away.
  2. The Right Thermostat Setting – Are you really going to notice the difference between 72°F and 69°F? Probably not, but you will save about 3% off of your monthly heating bill for every degree you turn the thermostat down. The same goes in the summer too, just backwards.
  3. Programmable Thermostats – And while we are on the subject of thermostats, it is a good idea to invest in a new one with programmable settings. That way you will be able to set your house to be warm when you will be there and you do not have to pay to keep it warm all day long if it is empty.
  4. Water Heater Temperature – Most hot water heaters are set to about 140°F. However, you really only need your water to be at 120°F. So turn down the hot water heater and you will save a lot.
  5. Ceiling Fans – Ceiling fans can help keep you cooler in the summer and warmer in the winter. Plus, they cost very little to run so they are a great investment.
  6. Light Bulbs – Switching to energy efficient fluorescent bulbs all over your house will save you a ton even though they cost a bit more to begin with.
  7. Lights Out – But energy efficient bulbs will only get you so far. You should also be sure to turn off the lights in any room you are not using.
  8. Insulation – Proper insulation will go a long way towards keeping in the temperature controlled air that you want and keeping out the outdoor air that you do not.
  9. Power Strips – Many home appliances draw a small amount of power even when they are not turned on. Use a power strip to easily cut the power to them completely and eliminate that drain.
  10. Sealing Windows – Plenty of air can come and go through your windows as well. Upgrading to more energy efficient windows is certainly an option, but you can also help to seal up your home inexpensively by covering your windows with plastic.

Tags: , , , , ,
Posted in Energy Savings | Comments Off

WaterSense Labels

Friday, January 28th, 2011

215.346.7160

Many people know about the EPA’s EnergyStar certification, which is a third-party certification system that verifies manufacturers’ claims about the energy efficiency of home appliances. The EnergyStar label has helped hundreds of thousands of consumers choose high-efficiency, cost-effective appliances for their homes.

The EPA has also developed a certification for plumbing fixtures, called WaterSense. WaterSense labels can be found on a variety of products, including:

  • Bathroom sink faucets and accessories
  • Showerheads
  • Toilets

While there are specific guidelines for each category of plumbing fixture, in general, the WaterSense label indicates that the product is at least 20% more efficient than conventional products in its category, without sacrificing performance or comfort.

The goal of the WaterSense guidelines is to make a real difference in the amount of water consumed in the U.S. – and the numbers bear this out. Let’s take a look at what would happen if every household in the US installed WaterSense products in their bathrooms.

If every household in the U.S. installed WaterSense bathroom sink faucets, it would save 60 billion gallons of water and $600 million in water heating costs. If every U.S. household put in WaterSense showerheads, the US would use 250 fewer billion gallons of water annually and save $2.5 billion in water heating costs. And if every household in the US upgraded to a new, efficient WaterSense toilet, it would save 640 billion gallons of water a year.

More realistically, even if only 1 in 10 U.S. households upgraded to WaterSense products, we would save about 74 billion gallons of water a year and $1.5 billion on our water heating bills.

Like EPA EnergyStar products, WaterSense products can be found at most plumbing retailers.

The WaterSense label can also be applied to entire homes. Homes that have the WaterSense label have:

  • Efficient hot water systems that deliver hot water quickly to minimize waste and waiting
  • WaterSense plumbing fixtures
  • EnergyStar dishwashers and clothes washers
  • Regionally appropriate outdoor landscaping that requires minimal maintenance and watering

In addition, landscaping professionals can apply for WaterSense certification to show that they have training in water-efficient irrigation system design, installation, maintenance, and auditing.

Tags: , , , , , ,
Posted in Energy Savings | Comments Off

Effects of Excessive Snow on Heat Pumps

Thursday, January 27th, 2011

215.346.7160

Due to recent excessive snowfall, we wanted to pass along a few tips for our customers who own heat pump systems.

Heat Pumps and Snow

Excessive snow can reduce a heat pump's ability to heat your home.

1. Heat pumps draw air from the areas surrounding them (all four sides of the outdoor unit). It is important to clear these areas of snow and ice build up in order to allow air to freely reach the heat pump. This will allow the heat pump to operate as efficiently as possible and will alleviate strain on the heat pump.

2. If possible, the space (air gap) between the heat pump and the plastic or concrete pad that the unit itself sits on should be cleared of snow to allow for drainage. Customers who have had heat pumps installed by Carney will note that there are two concrete lentels (rectangular blocks of concrete) that sit on either side of the base of the heat pump. The area between those lentils is the area that should be cleared.

3. Generally speaking, most heat pumps discharge air in an upward direction from the top of the unit. It is important to make sure that this area is clear of snow and ice to allow air to easily discharge (this is the air that is being drawn from the sides of the unit noted in item #1).

A note to Carney customers for whom we have installed a Trane XLi heat pump system: Trane’s XLi series heat pumps employ a “Weathergaurd” top that is designed to protect the heat pump from the affects of snow and ice on the top of the unit. In most cases snow and ice on the top of the unit will have no impact on an XLi heat pump. Air is discharged from the sides of the upper part of the heat pump instead. This area can be distinguished from the intake area as it is a) darker in color, b) plastic as opposed to steel, c) has a wider air gap between the fins and d) the direction of the louvers points upwards at an approximate 45 degree angle as opposed to downwards at the steel louvers. We have installed several hundred of Trane’s XLi series heat pump each year since 2003, so there is a good chance that you may own one – which is very beneficial at this time!
To help you identify if you own a Trane XLi heat pump, the following link will take you to an image of a Trane XL20i, which employs the same “Weathergaurd” top found on Trane XL16i, XL15i, XL14i and XL13i. http://www.trane.com/Residential/Products/Heat-Pumps/XL20i-Heat-Pumps

4. DO NOT attempt to forcefully remove ice build up from any part of the heat pump. If you cannot remove snow or ice easily with a broom or brush, do not try to pry or chisel ice from the unit. Doing so could cause severe or irrepairable damage to the heat pump.

5. If your heat pump is located in an area that is subject to exposure to melting snow and ice (such as underneath an overhang or gutter that may be frozen), check the unit repeatedly to ensure that ice has not built up inside the heat pump.

6. If you cannot clear the heat pump of snow and ice for any reason, switch the system to “Emergency Heat” at the thermostat. This will turn the heat pump off and engage electric resistance heaters that are located inside in order to provide heat for your home. This is a more expensive mode of operation for a heat pump system, so we do not advise continuing in this mode for more than a few days. If at that time, the snow and ice around the heat pump has not melted, feel free to schedule a service call with Carney and a technician from our service team will be happy to assist you.

Finally, if you are a geothermal heat pump owner – you have nothing to worry about! There is no outdoor unit, so there is no concern of snow or ice!

Further heating information can be found on our Heating FAQ’s Page.
As always, feel free to contact us with any questions or concerns at 215.346.7160 .

Tags: , , , ,
Posted in Energy Savings, Heat Pump Systems, Heat Pumps, Heating, Trane | Comments Off

Water-Saving Tips and Tricks

Wednesday, January 26th, 2011

215.346.7160

Here are some of our favorite water-saving tips. They are easy to incorporate into your lifestyle – and can save you hundreds or even thousands of gallons of water a year.

Whole House

  • Check for leaks – you may save thousands of gallons a month! You can find leaks by looking, listening, and monitoring your water bill for unusually high usage. To check for toilet leaks, put food coloring in your tank. If it gets into the bowl without flushing, you have a leak. Don’t forget to look for leaks in your outdoor plumbing too.
  • Know where your master water shut-off valve is located. In the event of a major problem, you’ll save thousands of gallons of water – and maybe your possessions as well.

Outdoors

  • Adjust your sprinklers so that you water only your lawn – not your sidewalk or driveway.
  • Consider adding a patio or “outdoor room” to your home. You’ll have less lawn to water and will add thousands of dollars to your home’s value.
  • Do two chores at once – water the grass by washing your car or your pet on the lawn. Be sure to use natural, biodegradable soaps.
  • Have your plumber re-route your laundry waste water to your lawn (check with local authorities first to be sure this is legal in your town).

In the Bathroom

  • Turn off faucets when you’re not actively using water – such as when you’re lathering your hands, shaving, or brushing your teeth. You’ll save hundreds of gallons each month. New touchless water faucets (or very affordable converters for your existing faucet) make this easy and fun to do, especially for kids.
  • Shorten your shower by only a minute or two, and save 150 gallons of water a month. (You can do this by turning off the shower while you lather your hair.)
  • Replace your old showerhead with a new WaterSense water-saving showerhead. They’re inexpensive and easy to install. You’ll save up to 750 gallons a month (and it’s a great opportunity to get a nice style upgrade too!).
  • Install WaterSense-certified aerators on all your faucets – another inexpensive upgrade that can save hundreds of gallons a month.
  • Insulate hot water pipes so don’t have to run the water as long while you wait for it to heat up.
  • Plug the tub before turning the water on for your bath, then adjust the temperature as the tub fills up.
  • Keep a bucket in the shower to catch water as it heats up. Use this water to flush toilets or water plants.

In the Kitchen and Laundry Room

  • Install a tankless water heater near your kitchen sink so you don’t have to run the water while it warms up.
  • If your dishwasher is new, scrape off excess food, but don’t pre-rinse. Modern dishwashers are built to handle un-rinsed items.
  • Upgrade your old water-cooled refrigerator, air conditioner, or ice-maker to a new air-cooled model for a significant reduction in water use
  • When buying new appliances, look for the EnergyStar label, which guarantees high efficiency. Also, look for models that offer cycle and load size adjustments.
  • Run your dishwasher and clothes washer only when they are full – you can save up to 1,000 gallons a month.

Tags: , , , , , , ,
Posted in Energy Savings | Comments Off

The Beauty of Zone Heating

Friday, January 21st, 2011

215.346.7160

While it might not technically be a necessity, there are a lot of reasons why you might want to look into having a zone heating system installed in your home. Whether you’ve been using the same home heating system for a long time or are looking to have a new one installed, there’s never a bad time to have a zone heating system put in.

Most people think that the only thing that affects their home heating and cooling bills is the energy efficiency of their furnace or heat pump. However, that’s simply not always the case. Certainly, the more efficient your furnace or heat pump is, the lower your energy bills will be. But that doesn’t mean they’re as low as they could possibly be.

After all, if you don’t have a zone control system installed, you’re paying to heat your entire house every time you turn on the heat. Depending on the size of your house, that could mean you’re heating anywhere from two to 10 rooms or more that are unoccupied at the time. In fact, you could be paying to heat an entire empty wing of your home. And while you’ll pay less than you would if your heating system was less efficient, you’re still paying more than you need to.

With a zone control system, you can heat your home much more efficiently because you can control which areas of the house get the heat and which ones don’t. You can set multiple different temperatures for the different zones of your home, which allows you to keep the occupied areas warm while not forcing you to waste energy to heat unoccupied spaces.

Aside from the economic benefits of only heating the areas of your home that you need, zone control systems also can put an end to some of those contentious thermostat wars that go on in so many households. If the members of your household can never agree on what a comfortable temperature is, they can simply each set their own temperature for their own area of the house.

That way, everyone is happy and no one has to suffer uncomfortably. After all, you paid a lot for your state of the art home heating system. It’s only fitting that you should be able to get the most possible out of it.

Tags: , , , , , , ,
Posted in Energy Savings | Comments Off

« Older Entries